Hi all,
A few days ago I received a iPod touch from a friend which doesn't work anymore. It was booting and then showing a white screen like this one on youtube.
I tried to put it in DFU mode and used iTunes to restore it. After iTunes checked the firmware it reboots the iPod and a progress bar shows up. However before the progress bar starts filling up, the phone reboots with the white screen and iTunes gives an error.
After several different attempts to fix it I started iRecovery which gives the following output
Using 'printenv' in iRecovery doesn't give anything. I also tried to get it out of the reboot loop but without succes.
Does any of you have any idea's how to fix this? Thanks in advanced!
A few days ago I received a iPod touch from a friend which doesn't work anymore. It was booting and then showing a white screen like this one on youtube.
I tried to put it in DFU mode and used iTunes to restore it. After iTunes checked the firmware it reboots the iPod and a progress bar shows up. However before the progress bar starts filling up, the phone reboots with the white screen and iTunes gives an error.
After several different attempts to fix it I started iRecovery which gives the following output
Code:
$ ./irecovery -s
iRecovery - Recovery Utility
by westbaer
Thanks to pod2g, tom3q, planetbeing and geohot.
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI0:CE0
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI0:CE1
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI1:CE8
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI1:CE9
=======================================
::
:: iBoot for n81ap, Copyright 2011, Apple Inc.
::
:: BUILD_TAG: iBoot-1219.62.15
::
:: BUILD_STYLE: RELEASE
::
:: USB_SERIAL_NUMBER: CPID:8930 CPRV:20 CPFM:03 SCEP:02 BDID:08 ECD:000002BE7E156D0D IBFL:03 SRNM:[DJ6HC5J1DT77]
::
=======================================
[FTL:MSG] Apple NAND Driver (AND) RO
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI0:CE0
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI0:CE1
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI1:CE8
[NAND] h2fmiPrintConfig:423 Chip ID 98 EE 95 32 7A 55 on FMI1:CE9
[FTL:MSG] FIL_Init [OK]
[FTL:MSG] BUF_Init [OK]
[FTL:MSG] FPart Init [OK]
read new style signature 0x43313131 (line:389)
[FTL:MSG] VSVFL Register [OK]
[WMR:MSG] Metadata whitening is set in NAND signature
[FTL:MSG] VFL Init [OK]
[FTL:MSG] VFL_Open [OK]
[FTL:MSG] YAFTL Register [OK]
yaFTL::YAFTL_Open(l:3335): CXT is not valid . Performing full NAND R/O restore ...
[NAND] h2fmiReadSinglePage:1797 UECC ce 3 page 0x00120eab
[NAND] h2fmiReadSinglePage:1797 UECC ce 3 page 0x00120eab
yaFTL::_readPage(l:5798): we got read failure at x2845f block 0xa10 block status x1 scrub 0
[NAND] h2fmiReadSinglePage:1797 UECC ce 2 page 0x00120eab
[NAND] h2fmiReadSinglePage:1797 UECC ce 2 page 0x00120eab
yaFTL::_readPage(l:5798): we got read failure at x28415e block 0xa10 block status x1 scrub 0
[NAND] h2fmiReadSinglePage:1797 UECC ce 0 page 0x00120eab
[NAND] h2fmiReadSinglePage:1797 UECC ce 0 page 0x00120eab
yaFTL::_readPage(l:5798): we got read failure at x28415c block 0xa10 block status x1 scrub 0
[FTL:MSG] FTL_Open [OK]
BootFailure Count: 0 Panic Fail Count: 15
Entering recovery mode, starting command promptUsing 'printenv' in iRecovery doesn't give anything. I also tried to get it out of the reboot loop but without succes.
Does any of you have any idea's how to fix this? Thanks in advanced!
